你知道在进行搭建山东电缆桥架的目标，如何判断地面的距离比较合理，能够契合工人师父的整体设计规划呢，让我们苏鑫桥架工作人员带领大家学习一下吧。

　　You know how to judge the reasonable distance between the ground and the overall design plan of the worker Shifu when building the cable tray in Shandong. Let us Su Xin bridge staff lead you to learn.

　　使用“激光投线仪”确认顶棚通杆螺丝的位置，并使用电钻进行开孔。上图激光投线仪，确认安装支架支吊架位置。

　　Use a "laser line projector" to confirm the position of the ceiling through rod screws and use an electric drill for drilling. Confirm the position of the installation bracket support and hanger for the laser line projector shown above.

　　安装支架支吊架间距为3米，在直线与弯通连接处0.3米的位置使用吊架。安装支架的安装高度为2.5米。

　　Install brackets with a spacing of 3 meters between supports and hangers, and use hangers at a position of 0.3 meters at the connection between straight lines and bends. The installation height of the bracket is 2.5 meters.

　　确认通杆螺丝位置时建议比原来长度稍长几公分确保可以小幅度调整安装支架水平位置。 五、使用拉爆与通杆螺丝相结合将通杆螺丝固定在顶棚确定的位置，并在通杆螺丝的下端安装吊框，吊框选用安装支架厂商提供的原件。

　　When confirming the position of the through-hole screw, it is recommended to extend it a few centimeters longer than the original length to ensure that the horizontal position of the installation bracket can be adjusted slightly. 5、 Use a combination of pull-out and through-pole screws to fix the through-pole screws at the designated position on the ceiling, and install a hanging frame at the lower end of the through-pole screws. The hanging frame is selected from the original components provided by the installation bracket manufacturer.

　　安装支架连接处一端安装支架连接片上螺丝不上即可安装支架直线段安装时，直接将安装支架穿过吊框，连接缝使用联接片连接。

　　At one end of the installation bracket connection, if the screw on the bracket connection piece is not tightened, the bracket can be installed. When installing the straight section of the bracket, directly pass the installation bracket through the hanging frame, and use the connection piece to connect the connection seam.

　　并安装跨界软铜线：安装支架位置矫正与检查确保安装支架安装完成之后处于水平位置，如不符合要求应当立即进行调整。确保安装支架前端与后端处于同一直线上，如不符合要求立即进行调整。

　　And install cross-border flexible copper wire: correct and check the position of the installation bracket to ensure that it is in a horizontal position after installation. If it does not meet the requirements, it should be adjusted immediately. Ensure that the front and rear of the installation bracket are in the same straight line, and adjust immediately if they do not meet the requirements.

　　总之，山东电缆桥架的搭建需要确保安装支架连接处应有软通线连接，如没有应当立即增加。确保安装支架某一直线段起始端与末端应当有角铁加进行固定，安装支架超过一定距离时应当选用角铁支架进行固定。

相关文章：山东电缆桥架